fbpx

Spintly

Select your region

USA
India

INSTALLATION GUIDE :

INSTALLATION GUIDE

Spintly UNO-W

Model No : SU-014

Spintly UNO-W Reader with it’s elegant design provides seamless user experience that allows users to unlock doors with their smartphones.

Spintly UNO-W Reader with it’s elegant design provides seamless user experience that allows users to unlock doors with their smartphones.

1. Product Features and Specifications

1.1. Features

  • Wireless BLE Mesh Networking
  • Easy to Install and Set-up
  • Works without Internet
  • Cloud based platform
  • Smartphone based access
  • Card based access
  • Retrofit with legacy controllers over Wiegand

1.2. Electrical Specifications

  • Power source: 12V / 24V DC Input
  • Power consumption: 2.4W max at 12V

1.1. Features

  • Wireless BLE Mesh Networking
  • Easy to Install and Set-up
  • Works without Internet
  • Cloud based platform
  • Smartphone based access
  • Card based access
  • Retrofit with legacy controllers over Wiegand

1.2. Electrical Specifications

  • Power source: 12V / 24V DC Input
  • Power consumption: 2.4W max at 12V

2. Mechanical Dimensions

  • Length = 90 mm
  • Width = 49.5 mm
  • Depth = 29 mm
  • Length = 90 mm
  • Width = 49.5 mm
  • Depth = 29 mm

3. Mounting Instructions :

Step 1. Pre-drill the mounting locations using Drill Template provided in the box.
Then mount the back plate on the wall with the help of wall plugs and screws (4 qty) as shown above.

Step 2. Strip and connect the wires as per the pigtail color code and connection diagram. Refer Fig 4.2.1 under Wiring Instructions – Section 4.

Step 3. Once the connection is done, pass the pigtail through the back plate opening

Step 4. Mount the reader on the back plate and secure it using M3 x 8mm screws (2qty)

Step 1. Pre-drill the mounting locations using Drill Template provided in the box.
Then mount the back plate on the wall with the help of wall plugs and screws (4 qty) as shown above.

Step 2. Strip and connect the wires as per the pigtail color code and connection diagram. Refer Fig 4.2.1 under Wiring Instructions – Section 4.

Step 3. Once the connection is done, pass the pigtail through the back plate opening

Step 4. Mount the reader on the back plate and secure it using M3 x 8mm screws (2qty)

4. Wiring Instructions :

4.1. Pigtail color code

UNO-W reader is equipped with a 10 core pigtail required during the connection process. The table below describes the signal names along with their corresponding color code.

The reader supports various modes of configuration. The connection of wires will differ based on the selected configuration. To ensure proper setup and functionality, refer to the configurations listed below.

4.2. Configuration 1 : Standalone Spintly Reader

Installation type : Entry Reader and REX

4.3. Configuration 2 : Spintly Entry with Exit Reader

Installation type : Entry-Exit

  • In this mode, both the entry and exit Spintly readers will share the same power lines. Connect together the VIN wires of both the readers. Similarly for GND wires (ground).
  • Short VIN wire to COMMON wire of Entry Reader
  • Short NC wire of Entry Reader to COMMON wire of Exit Reader
  • Connect the locking mechanism (Strike lock or Magnetic lock) to NC wire of Exit Reader
  • The sensor inputs (REX and Door sensor) should be connected to Exit reader

4.4. Configuration 3 : Spintly Reader with Wiegand Controller

Installation type : Retrofit (Wiegand enabled)

  • Below mentioned 5 wires should be connected from Spintly Reader to Wiegand controller
  • Power wires — V+ and GND
  • Communication wires — DATA0, DATA1, and GLED (refer the color code shown in above table) to the respective terminals of Wiegand controller.

           Note : When used in Wiegand mode, use orange wire as GLED signal

Note : When used in Wiegand mode, use orange wire as GLED signal

  • Connect the locking mechanism (Strike lock or Magnetic lock) to NC (in case of mag lock) wire of Exit Reader
  • The sensor input (REX) should be connected to controller.

       Door Sensor cannot be used in this mode

Door Sensor cannot be used in this mode

Get in touch